Type Alias Xosc

pub type Xosc = Reg<XoscSpec>;

XOSC (rw) register accessor: External Multipurpose Crystal Oscillator (XOSC) Control

You can read this register and get xosc::R. You can reset, write, write_with_zero this register using xosc::W. You can also modify this register. See API.

For information about available fields see xosc module

Aliased Type

struct Xosc { /* private fields */ }

Implementations

impl<REG: RegisterSpec> Reg<REG>

pub fn as_ptr(&self) -> *mut REG::Ux

Returns the underlying memory address of register.

let reg_ptr = periph.reg.as_ptr();

impl<REG: Readable> Reg<REG>

pub fn read(&self) -> R<REG>

Reads the contents of a Readable register.

You can read the raw contents of a register by using bits:

let bits = periph.reg.read().bits();

or get the content of a particular field of a register:

let reader = periph.reg.read();
let bits = reader.field1().bits();
let flag = reader.field2().bit_is_set();

impl<REG: Resettable + Writable> Reg<REG>

pub fn reset(&self)

Writes the reset value to Writable register.

Resets the register to its initial state.

pub fn write<F>(&self, f: F)

where F: FnOnce(&mut W<REG>) -> &mut W<REG>,

Writes bits to a Writable register.

You can write raw bits into a register:

periph.reg.write(|w| unsafe { w.bits(rawbits) });

or write only the fields you need:

periph.reg.write(|w| w
    .field1().bits(newfield1bits)
    .field2().set_bit()
    .field3().variant(VARIANT)
);

or an alternative way of saying the same:

periph.reg.write(|w| {
    w.field1().bits(newfield1bits);
    w.field2().set_bit();
    w.field3().variant(VARIANT)
});

In the latter case, other fields will be set to their reset value.

impl<REG: Writable> Reg<REG>

pub unsafe fn write_with_zero<F>(&self, f: F)

where F: FnOnce(&mut W<REG>) -> &mut W<REG>,

Writes 0 to a Writable register.

Similar to write, but unused bits will contain 0.

Safety

Unsafe to use with registers which don’t allow to write 0.

impl<REG: Readable + Writable> Reg<REG>

pub fn modify<F>(&self, f: F)

where for<'w> F: FnOnce(&R<REG>, &'w mut W<REG>) -> &'w mut W<REG>,

Modifies the contents of the register by reading and then writing it.

E.g. to do a read-modify-write sequence to change parts of a register:

periph.reg.modify(|r, w| unsafe { w.bits(
   r.bits() | 3
) });

or

periph.reg.modify(|_, w| w
    .field1().bits(newfield1bits)
    .field2().set_bit()
    .field3().variant(VARIANT)
);

or an alternative way of saying the same:

periph.reg.modify(|_, w| {
    w.field1().bits(newfield1bits);
    w.field2().set_bit();
    w.field3().variant(VARIANT)
});

Other fields will have the value they had before the call to modify.

Trait Implementations

impl<REG: Readable> Debug for Reg<REG>

where R<REG>: Debug,

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl<REG: RegisterSpec> Send for Reg<REG>

where REG::Ux: Send,