#[repr(C)]
#[doc = "16-bit Counter with Two 16-bit Compares"]
#[doc(alias = "MODE1")]
pub struct Mode1 {
ctrla: Ctrla,
ctrlb: Ctrlb,
evctrl: Evctrl,
intenclr: Intenclr,
intenset: Intenset,
intflag: Intflag,
dbgctrl: Dbgctrl,
_reserved7: [u8; 0x01],
syncbusy: Syncbusy,
freqcorr: Freqcorr,
_reserved9: [u8; 0x03],
count: Count,
_reserved10: [u8; 0x02],
per: Per,
_reserved11: [u8; 0x02],
comp: [Comp; 4],
_reserved12: [u8; 0x18],
gp: [Gp; 4],
_reserved13: [u8; 0x10],
tampctrl: Tampctrl,
timestamp: Timestamp,
tampid: Tampid,
_reserved16: [u8; 0x14],
bkup: [Bkup; 8],
}
impl Mode1 {
#[doc = "0x00 - MODE1 Control A"]
#[inline(always)]
pub const fn ctrla(&self) -> &Ctrla {
&self.ctrla
}
#[doc = "0x02 - MODE1 Control B"]
#[inline(always)]
pub const fn ctrlb(&self) -> &Ctrlb {
&self.ctrlb
}
#[doc = "0x04 - MODE1 Event Control"]
#[inline(always)]
pub const fn evctrl(&self) -> &Evctrl {
&self.evctrl
}
#[doc = "0x08 - MODE1 Interrupt Enable Clear"]
#[inline(always)]
pub const fn intenclr(&self) -> &Intenclr {
&self.intenclr
}
#[doc = "0x0a - MODE1 Interrupt Enable Set"]
#[inline(always)]
pub const fn intenset(&self) -> &Intenset {
&self.intenset
}
#[doc = "0x0c - MODE1 Interrupt Flag Status and Clear"]
#[inline(always)]
pub const fn intflag(&self) -> &Intflag {
&self.intflag
}
#[doc = "0x0e - Debug Control"]
#[inline(always)]
pub const fn dbgctrl(&self) -> &Dbgctrl {
&self.dbgctrl
}
#[doc = "0x10 - MODE1 Synchronization Busy Status"]
#[inline(always)]
pub const fn syncbusy(&self) -> &Syncbusy {
&self.syncbusy
}
#[doc = "0x14 - Frequency Correction"]
#[inline(always)]
pub const fn freqcorr(&self) -> &Freqcorr {
&self.freqcorr
}
#[doc = "0x18 - MODE1 Counter Value"]
#[inline(always)]
pub const fn count(&self) -> &Count {
&self.count
}
#[doc = "0x1c - MODE1 Counter Period"]
#[inline(always)]
pub const fn per(&self) -> &Per {
&self.per
}
#[doc = "0x20..0x28 - MODE1 Compare n Value"]
#[inline(always)]
pub const fn comp(&self, n: usize) -> &Comp {
&self.comp[n]
}
#[doc = "Iterator for array of:"]
#[doc = "0x20..0x28 - MODE1 Compare n Value"]
#[inline(always)]
pub fn comp_iter(&self) -> impl Iterator<Item = &Comp> {
self.comp.iter()
}
#[doc = "0x40..0x50 - General Purpose"]
#[inline(always)]
pub const fn gp(&self, n: usize) -> &Gp {
&self.gp[n]
}
#[doc = "Iterator for array of:"]
#[doc = "0x40..0x50 - General Purpose"]
#[inline(always)]
pub fn gp_iter(&self) -> impl Iterator<Item = &Gp> {
self.gp.iter()
}
#[doc = "0x60 - Tamper Control"]
#[inline(always)]
pub const fn tampctrl(&self) -> &Tampctrl {
&self.tampctrl
}
#[doc = "0x64 - MODE1 Timestamp"]
#[inline(always)]
pub const fn timestamp(&self) -> &Timestamp {
&self.timestamp
}
#[doc = "0x68 - Tamper ID"]
#[inline(always)]
pub const fn tampid(&self) -> &Tampid {
&self.tampid
}
#[doc = "0x80..0xa0 - Backup"]
#[inline(always)]
pub const fn bkup(&self, n: usize) -> &Bkup {
&self.bkup[n]
}
#[doc = "Iterator for array of:"]
#[doc = "0x80..0xa0 - Backup"]
#[inline(always)]
pub fn bkup_iter(&self) -> impl Iterator<Item = &Bkup> {
self.bkup.iter()
}
}
#[doc = "CTRLA (rw) register accessor: MODE1 Control A\n\nYou can [`read`](crate::Reg::read) this register and get [`ctrla::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`ctrla::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@ctrla`]
module"]
#[doc(alias = "CTRLA")]
pub type Ctrla = crate::Reg<ctrla::CtrlaSpec>;
#[doc = "MODE1 Control A"]
pub mod ctrla;
#[doc = "CTRLB (rw) register accessor: MODE1 Control B\n\nYou can [`read`](crate::Reg::read) this register and get [`ctrlb::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`ctrlb::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@ctrlb`]
module"]
#[doc(alias = "CTRLB")]
pub type Ctrlb = crate::Reg<ctrlb::CtrlbSpec>;
#[doc = "MODE1 Control B"]
pub mod ctrlb;
#[doc = "EVCTRL (rw) register accessor: MODE1 Event Control\n\nYou can [`read`](crate::Reg::read) this register and get [`evctrl::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`evctrl::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@evctrl`]
module"]
#[doc(alias = "EVCTRL")]
pub type Evctrl = crate::Reg<evctrl::EvctrlSpec>;
#[doc = "MODE1 Event Control"]
pub mod evctrl;
#[doc = "INTENCLR (rw) register accessor: MODE1 Interrupt Enable Clear\n\nYou can [`read`](crate::Reg::read) this register and get [`intenclr::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`intenclr::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@intenclr`]
module"]
#[doc(alias = "INTENCLR")]
pub type Intenclr = crate::Reg<intenclr::IntenclrSpec>;
#[doc = "MODE1 Interrupt Enable Clear"]
pub mod intenclr;
#[doc = "INTENSET (rw) register accessor: MODE1 Interrupt Enable Set\n\nYou can [`read`](crate::Reg::read) this register and get [`intenset::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`intenset::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@intenset`]
module"]
#[doc(alias = "INTENSET")]
pub type Intenset = crate::Reg<intenset::IntensetSpec>;
#[doc = "MODE1 Interrupt Enable Set"]
pub mod intenset;
#[doc = "INTFLAG (rw) register accessor: MODE1 Interrupt Flag Status and Clear\n\nYou can [`read`](crate::Reg::read) this register and get [`intflag::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`intflag::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@intflag`]
module"]
#[doc(alias = "INTFLAG")]
pub type Intflag = crate::Reg<intflag::IntflagSpec>;
#[doc = "MODE1 Interrupt Flag Status and Clear"]
pub mod intflag;
#[doc = "DBGCTRL (rw) register accessor: Debug Control\n\nYou can [`read`](crate::Reg::read) this register and get [`dbgctrl::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`dbgctrl::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@dbgctrl`]
module"]
#[doc(alias = "DBGCTRL")]
pub type Dbgctrl = crate::Reg<dbgctrl::DbgctrlSpec>;
#[doc = "Debug Control"]
pub mod dbgctrl;
#[doc = "SYNCBUSY (r) register accessor: MODE1 Synchronization Busy Status\n\nYou can [`read`](crate::Reg::read) this register and get [`syncbusy::R`]. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@syncbusy`]
module"]
#[doc(alias = "SYNCBUSY")]
pub type Syncbusy = crate::Reg<syncbusy::SyncbusySpec>;
#[doc = "MODE1 Synchronization Busy Status"]
pub mod syncbusy;
#[doc = "FREQCORR (rw) register accessor: Frequency Correction\n\nYou can [`read`](crate::Reg::read) this register and get [`freqcorr::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`freqcorr::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@freqcorr`]
module"]
#[doc(alias = "FREQCORR")]
pub type Freqcorr = crate::Reg<freqcorr::FreqcorrSpec>;
#[doc = "Frequency Correction"]
pub mod freqcorr;
#[doc = "COUNT (rw) register accessor: MODE1 Counter Value\n\nYou can [`read`](crate::Reg::read) this register and get [`count::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`count::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@count`]
module"]
#[doc(alias = "COUNT")]
pub type Count = crate::Reg<count::CountSpec>;
#[doc = "MODE1 Counter Value"]
pub mod count;
#[doc = "PER (rw) register accessor: MODE1 Counter Period\n\nYou can [`read`](crate::Reg::read) this register and get [`per::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`per::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@per`]
module"]
#[doc(alias = "PER")]
pub type Per = crate::Reg<per::PerSpec>;
#[doc = "MODE1 Counter Period"]
pub mod per;
#[doc = "COMP (rw) register accessor: MODE1 Compare n Value\n\nYou can [`read`](crate::Reg::read) this register and get [`comp::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`comp::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@comp`]
module"]
#[doc(alias = "COMP")]
pub type Comp = crate::Reg<comp::CompSpec>;
#[doc = "MODE1 Compare n Value"]
pub mod comp;
#[doc = "GP (rw) register accessor: General Purpose\n\nYou can [`read`](crate::Reg::read) this register and get [`gp::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`gp::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@gp`]
module"]
#[doc(alias = "GP")]
pub type Gp = crate::Reg<gp::GpSpec>;
#[doc = "General Purpose"]
pub mod gp;
#[doc = "TAMPCTRL (rw) register accessor: Tamper Control\n\nYou can [`read`](crate::Reg::read) this register and get [`tampctrl::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`tampctrl::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@tampctrl`]
module"]
#[doc(alias = "TAMPCTRL")]
pub type Tampctrl = crate::Reg<tampctrl::TampctrlSpec>;
#[doc = "Tamper Control"]
pub mod tampctrl;
#[doc = "TIMESTAMP (r) register accessor: MODE1 Timestamp\n\nYou can [`read`](crate::Reg::read) this register and get [`timestamp::R`]. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@timestamp`]
module"]
#[doc(alias = "TIMESTAMP")]
pub type Timestamp = crate::Reg<timestamp::TimestampSpec>;
#[doc = "MODE1 Timestamp"]
pub mod timestamp;
#[doc = "TAMPID (rw) register accessor: Tamper ID\n\nYou can [`read`](crate::Reg::read) this register and get [`tampid::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`tampid::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@tampid`]
module"]
#[doc(alias = "TAMPID")]
pub type Tampid = crate::Reg<tampid::TampidSpec>;
#[doc = "Tamper ID"]
pub mod tampid;
#[doc = "BKUP (rw) register accessor: Backup\n\nYou can [`read`](crate::Reg::read) this register and get [`bkup::R`]. You can [`reset`](crate::Reg::reset), [`write`](crate::Reg::write), [`write_with_zero`](crate::Reg::write_with_zero) this register using [`bkup::W`]. You can also [`modify`](crate::Reg::modify) this register. See [API](https://docs.rs/svd2rust/#read--modify--write-api).\n\nFor information about available fields see [`mod@bkup`]
module"]
#[doc(alias = "BKUP")]
pub type Bkup = crate::Reg<bkup::BkupSpec>;
#[doc = "Backup"]
pub mod bkup;